Clinical and Radiographic Examination of the Equine Foot
Lameness is one of the most frequently encountered problems in equine practice. The foot is involved, either directly or indirectly, in the large majority of lameness cases, because it is the first line of defense for the animal. The health of the foot plays a major role in the fight or flight response that has preserved this noble species for several thousand years. “No foot, no horse” is an adage that has been used across the world for centuries. This indisputable statement encapsulates the importance of a healthy foot; however, we know less about the foot than about almost any other part of the horse, and it is the one piece of anatomy that is dependent on a lay profession for the preservation of its health and function.
Worldwide, farriers bear much of the responsibility for maintaining or restoring the health of the horse’s foot. For centuries, their knowledge and skills have been self-taught, without the benefit of a formal educational program. Their basic job description is to keep the foot healthy by using effective but primitive methods to control the ill effects of horn growth and wear and tear on the hoof capsule with little or no information about the effects of these procedures on the sensitive soft tissues, vascular supply, or bone. Veterinarians, on the other hand, have been taught anatomy, physiology, and basic examination techniques; however, they often have limited working knowledge of the foot and little or no farriery skills.
Both professions play important and complementary roles. Veterinarians and farriers alike are often asked to examine the foot for a variety of reasons, including developmental problems, gait analysis, lameness exams, and pre-purchase exams. In many cases, the opinions that result are as diverse as the backgrounds and areas of expertise of the respective professionals. Combining the knowledge and skills of a competent farrier with the medical and surgical training of the veterinarian greatly enhances the diagnostic and prognostic potential of both clinical and radiographic examinations. Working together also advances the professional standing of veterinarians and farriers.
Clinical and radiographic examinations of the foot are simply discovery exercises. Numerous authors have described their methods and techniques in detail. However, despite the vast amount of written material on the subject, obtaining meaningful information about the foot remains a challenge for veterinarians and farriers. The key is to use a disciplined, methodical approach that is designed to disclose and define the various normal soft tissue parameters, normal bone anatomy, and normal hoof capsule anatomy as well as the inter-relation of each component. The protocol should also reveal the response of these structures to the forces imposed by ground contact, supporting tissues, and horse’s body weight.
Seeking and defining specific pieces of information in a consistent, repeatable manner for each foot in each horse greatly enhances the practitioner’s understanding and knowledge regarding the vast range of normal--the real information you want. When examining a foot or a radiograph, look for all the normal areas first; what is leftover points to the problem you seek. This simple approach effectively helps avoid misinterpretation, a common result of forming an opinion without sufficient diagnostic information: for example, making presumptions concerning the clinical relevance of a radiographic lesion without consideration of the history or physical findings.
2. Clinical Examination
Regardless of the purpose of the examination, the physical exam is the most important aspect of evaluating the equine foot. The extent and nature of the exam must be tailored to the situation but must also take into account the demands of the client. Good horsemanship, good working knowledge of the foot, and basic farriery skills are other prerequisites for a proper and safe examination.
A complete history, which clearly describes the complaint, complements the physical exam and adds context to any clinical findings. Listen to the history as you examine the foot, but do not jump to conclusions or be swayed by the opinions or conclusions of others. Visually inspect the foot before picking it up and feel the hoof capsule with your hands, noting its many unique characteristics.
Although certain generalities can be made, there is a range of normal for hoof characteristics that are influenced by the horse’s breed, age, environment, and use. Considering the variability imposed by these factors, the range of normal can be very broad. The importance of understanding the variability in structure of the healthy equine foot lies in identifying subtle deviations from normal that are of clinical significance. These early distortions are easily missed if the normal parameters for a horse of that breed, age, environment, and use are not appreciated.
The following example details the requirements for adequately defining normal for a particular horse. Let us consider the forefoot of a 3-yr-old Thoroughbred horse, bred for racing but used as a non-competitive riding horse in central Kentucky. That foot would probably have the following characteristics: a hoof angle between 50° and 58°; a heel angle approximately 15-20° less; a relatively straight wall (i.e., no flaring, dishing, or bulging); a width approximately 5 in (measured at the widest point); a mass of digital cushion 2-3 in (discussed later); a hoof wall thickness of 0.375-0.5 in at the toe and the bars; a hoof wall perhaps one-half as thick at the quarters; a sole with a moderate cup (3-5 mm in height); a frog in contact with the ground (although it would also be normal for this horse to have a relatively flat sole, i.e., little or no cup, and a large, flat frog); and a hoof wall with a solid appearance and a glossy surface.
We must leave behind the “ideal” of the normal equine foot depicted by artists in veterinary and farriery texts for the past century or more. In my experience, hoof angles and heel angles do not match on any normal foot. Additionally, the “ideal” toe angles of 45° for front feet and 50° for hind feet are far from normal as they do not match the pastern angles. One must become a connoisseur of horses’ feet and begin to build a personal data bank of normal for particular breeds, age groups, environments, and uses.
The Seat of Pain
When dealing with a lame horse, most authors consider the physical exam simply a means of reaching a diagnosis, i.e., giving the problem a name. While this approach certainly satisfies one of the goals of the exam (to identify the problem), years of experience as an equine podiatrist have made me very aware that most owners want a fix and could care less about a diagnosis.
As I am going through a lameness work-up, I focus on identifying the area(s) of pain rather than specific pathology. Dividing the foot into two halves, front and back, then dividing further into quadrants (medial and lateral, front and back) offers a simple way of isolating the specific area of inflammation or seat of pain (Fig. 1, A and B).
Dividing the foot into four basic zones helps me determine whether the components in each zone fit within the range of normal for that particular animal. With my understanding of radiographic anatomy (again bearing in mind the range of normal), I visualize the bone and associated soft tissues superimposed over the hoof (Fig. 2). Any finding that falls outside the range of normal is considered relevant, because it contributes to the dysfunction of the foot as an integrated unit, and thus, probably plays a role in the current lameness problem.
Simply cleaning the foot thoroughly and lightly rasping across the ground surface of the hoof can reveal several areas of possible concern (Fig. 3). Each of these areas is a map of a potential problem: examine each thoroughly before moving on. Remember to look for all the normal areas first, and what is leftover often points to the problem that you are attempting to identify.
After a quick visual exam, I palpate, using thumb pressure, to locate areas of increased sensitivity along the coronary band, the bulbs of the heel, and even over the sole on thin-soled feet. Hoof testers should be used with great care, because inappropriate use causes the horse to anticipate further pain and show an exaggerated response to even light pressure.
When applying hoof testers, use a very soft touch. All that is needed to identify areas of increased sensitivity is just enough pressure to cause slight movement of thin horn (e.g., the sole in a thin-soled horse). Also, be aware of how you are holding the horse’s leg. If, by positioning the limb between your knees so that you are comfortable, the horse is made uncomfortable, you may elicit a response that has nothing to do with the foot.
It is easy to abduct the limb too far when placing the horse’s lower limb between your knees. To avoid this situation, note where the horse’s body is in relation to the foot when you first pick up the leg. Try to maintain that orientation when placing the limb between your knees--i.e., put yourself where the foot is or have someone hold the limb for you (Fig. 4, A–D).
The Failing Structure
Distinguishing the abnormal area(s) allows me to identify the part(s) of the system that are failing and affecting the integrity of the whole. Simply recognizing the failing structure(s) as the primary problem --the underlying cause of any secondary bone and/or soft tissue disease--gives new meaning to the discovery exercise and places new emphasis on the findings. The following example details this concept.
Race horses, or in fact, any speed horses, with a sole less than 10 mm, a zero or negative palmar angle (the angle of the palmar/planter margin of the third phalanx [PIII] relative to either the ground surface of the hoof capsule or the ground itself [depending on whether the shoe or therapeutic device is altering the relationship between PIII and the ground]), a loss of cushion mass (see below), an obvious medial–lateral imbalance, and a history of foot pain are often diagnosed with navicular disease, pedal osteitis, or bruised feet. Any of these diagnoses may be correct, and the associated pathology may be contributing to the present lameness. However, more important is the fact that the essential protective function of the hoof capsule and the shock-absorbing features of the cushion network are seriously compromised, and the cumulative effects of these failing systems are now of paramount importance.
The “diagnosis” in this case is, thus, multifaceted. However, it can be simplified by describing the situation as one of mild, moderate, or excessive horn loss associated with mild, moderate, or excessive compromise of the soft tissues. Instead of being focused on a medical diagnosis (which may well be challenged by another veterinarian or farrier) and a quick fix to satisfy the immediate demands of the client, identifying the failing systems allows the focus to be placed on a solution, which, in this case, involves restoring the much needed hoof mass.
The depth of the digital cushion can be estimated by placing your thumb in the shallow depression between the heel bulbs and placing the index finger of the same hand on the center of the frog (Fig. 5). In light breed horses with strong, healthy heels, the distance between thumb and fingertip is in the range of 3–3.5 in. When this distance is well short of the normal range, one can expect to see evidence of soft tissue compromise radiographically. This simple observation, coupled with noting the slope of the coronary band relative to the ground, also allows an estimation of sole depth (the vertical distance between the palmar/plantar margin of PIII [at the apex] and the outer surface of the sole) and palmar angle.
Figures 6 and 7 illustrate how these observations correlate with radiographic findings. Note the dif- ference in slope of the coronary band, angle of the horn tubules at the heel, and depth of cushion between the two horses (Fig. 6, A and B). Compare these photographs with lateral radiographs of the same feet (Fig. 7, A and B). Incidentally, in my experience, hind feet with a zero or negative plantar angle (wings of PIII level with or lower than the apex) are often associated with pain in the lumbar area or croup. Back pain in these horses frequently diminishes once heel mass is improved and a normal plantar angle is restored.
It is necessary to remove the horse’s shoe to thoroughly examine the foot, especially when the primary problem cannot be identified with the shoe on. At the very least, the shoe prevents examination of the bearing surface of the wall, the terminal laminae, and the perimeter of the sole. However, care must be taken when pulling shoes. In feet with fragile walls, raised nail clinches, or special shoeing packages, the shoes are best removed by a competent farrier, unless you have considerable farriery expertise.
A good sense of smell can be a valuable aid in examining the foot. We all know the smell of a foot with thrush. However, your olfactory sense can also help you identify digital sepsis. With experience, it is even possible to distinguish soft tissue necrosis from septic processes involving bone. Again, attention to detail is the key to refining one’s examination skills.
- Physical examination is the most important part of evaluating the foot
- Develop a methodical approach, and use it every time
- Look for normal first (bearing in mind the range of normal for the horse’s breed, age, environment, and use); what is leftover points to the problem you seek
- Localize the seat of pain to one or more quadrants
- Visualize the underlying bone and associated soft tissues when looking at the hoof
- Think in terms of identifying the failing structure(s)
3. Radiographic Examination
Much has been written about specific views for imaging the equine foot. Almost without exception, the primary objective of these views is examination of bone (PIII, navicular bone, and/or coffin joint surfaces). Little or no attention is paid to the soft tissues within the hoof capsule. This approach seriously limits the scope and accuracy of the radiographic examination, and thus, its value in developing an action plan for managing lameness involving the foot.
The coffin bone is suspended within its protective shell by soft tissues, whose health is crucial to the structural and functional integrity of the foot as a whole. Dysfunction is inevitable when any of the soft tissues are compromised or strained beyond their normal limits. Over the many years I have worked as an equine podiatrist, I have come to appreciate the fact that soft tissue pathology is present to some degree in every footsore horse. Thus, evaluation of the soft tissue zones within the hoof capsule is an extremely important part of radiographic examination of the foot.
Evaluating the Soft Tissues
Although it is true that radiography is relatively poor at imaging soft tissues, a lot of information about the soft tissues within the foot can be gleaned from good quality radiographs taken with soft tissue detail in mind (discussed in the next section). At the very least, the width of the corium and horn can be accurately measured for both hoof wall and sole, provided the outer surface of the dorsal hoof wall is delineated using radiopaque material. I use a line of barium pastea along the face of the hoof, starting at the proximal border and extending to the ground surface (Fig. 11). The ground surface is defined either by the shoe or by a radiopaque marker in the surface of the positioning block. I measure the following indices on all routine lateral films (Fig. 8).
Sole depth is routinely measured at the distal tip, or apex, of PIII (Fig. 8). A normal, healthy foot has a sole depth of at least 15 mm.
Based on venographic studies in a wide variety of horses, I consider a sole depth of less than 15 mm to be clinically significant. In a normal foot, the papillae of the solar corium seem to need a space of at least 10 mm between the palmar surface of PIII and the cornified layer of the sole for adequate vascular filling, and at least 5 mm of cornified sole is required to protect the solar corium. Venograms in horses with a sole depth <15 mm show solar papillae that are bent, compressed, or even absent. This distortion or compression surely inhibits sole growth, creating a vicious cycle of thin, tender soles.
Dorsal Horn-Lamellar Zone Width
Dorsal horn-lamellar (H-L) zone width is defined as the distance between the dorsal surface of PIII and the outer surface of the dorsal hoof wall (measured with the ruler perpendicular to the dorsal face of PIII)--i.e., width of the dorsal H-L zone (Fig. 8). Dorsal H-L zone width can be measured anywhere along the dorsal face of PIII, but I routinely measure it at two locations: just below the extensor process and near the distal tip of PIII. I record the measurements as proximal/distal (e.g., 15/15, meaning that the dorsal H-L zone is 15 mm at both locations). In a normal adult foot, the measurements should be the same proximally as distally (i.e., both numbers are identical). In the immature foot, the proximal value may be greater than the distal value.
Normal dorsal H-L zone width in Quarter Horses, Thoroughbreds, and most other light horse breeds is 15–16 mm. In Standardbreds, the H-L zone normally is a little wider, averaging 20 mm. Normal H-L zone width for Warmbloods depends on the size of the foot; in many cases, it is similar to that for light breeds. Once again, an appreciation of the range of normal for that type and size of horse is essential for accurately interpreting this area.
Dorsal H-L zone width is an important measurement, as this zone widens in conditions that affect the laminar corium, laminar attachments, and wall thickness. Laminitis and white line disease are two common and clinically important conditions in which the dorsal H-L zone widens. Widening as one moves down the hoof wall from proximal to distal (i.e., H-L zone wider distally than proximally) may also be seen with other conditions.
This assessment, when used with the palmar angle (Fig. 9B), provides a meaningful way to identify and describe displacement of PIII. I believe that the conventional method of identifying and quantitating PIII rotation is inaccurate and misleading. The fact that the hoof capsule can be substantially altered by the farrier reduces evidence of rotation. Drawing straight lines along the irregular hoof wall and irregular face of PIII is subjective at best, and the wall is constantly being altered by the growth and the disease process. Therefore, I believe the whole basis of this measurement (PIII hoof wall angle) is seriously flawed.
Traditionally, measuring capsule rotation as a means to diagnose laminitis has also created the misconception that simply rasping the horn wall back to a parallel relationship with the face of PIII is an effective means of treating the syndrome. Very serious or life-threatening lamellar swelling often occurs without even a subtle hint of rotation. Therefore, the significance of rotation as it relates to pathology is questionable.
On a good soft tissue detail lateral film, one can readily identify the linear radiopaque zone that equally divides the H-L zone in most normal horses. For example, in a foot with a dorsal H-L zone width of 15 mm, each zone measures 7.5 mm. When widening of the dorsal H-L zone is found, evaluation of the width of each zone is important, because it can provide diagnostically and prognostically valuable information. For example, the lamellar zone widens in laminitis (Fig. 9B) whereas it is the horn zone that widens in white line disease (Fig. 9A). (Note: The outer surface of the dorsal hoof wall must be accurately represented by radiopaque material for measurement of the horn zone to be accurate.)
Coronary-Extensor Process Distance
Coronary-extensor (C-E) distance is the vertical distance between the most proximal extent of the outer hoof wall (immediately below the coronary band) and the top of the extensor process of PIII--i.e., coronary-extensor process distance (Fig. 8). In most normal horses, it is 0-15 mm. The C-E distance can be accurately measured only if the radiopaque marker on the dorsal hoof wall extends all the way to the proximal limit of the wall. This measurement can be important in confirming displacement of PIII, provided a baseline is established for that horse before or at the onset of the disease process.
Palmar angle can be measured relative to (1) the ground surface of the hoof capsule or (2) the ground itself. Using (1), the angle is largely unrelated to the mechanics of the shoe or other device that may be attached to the foot. It provides information about the structural integrity of the soft tissues in the heel area, especially the digital cushion. Using (2), the palmar angle is also indicative of the mechanical effect of any shoe/device that is attached to the foot (Fig. 18A).
In most healthy feet with strong heels and robust digital cushions, the palmar angle is positive, meaning that the wings of PIII are higher than the apex (Fig. 7B). As with most other indices, the range of normal for palmar angle is dependent, in part, on the horse’s breed. Breeds that tend to have upright hooves typically have higher palmar angles than breeds that have naturally lower hoof angles. The shoeing package can also affect the palmar angle, which must be borne in mind when measuring palmar angle relative to the ground.
A high palmar angle (relative to the range of normal for that breed) may be found in horses with club feet, laminitis, or certain other pathological conditions. A negative palmar angle (wings of PIII lower than the apex) indicates substantial loss of structural integrity in the heel area, a situation that can usually be predicted simply by looking at the foot and estimating the depth of the digital cushion.
In addition to these measurements, a high-quality radiograph taken at a soft exposure (see below) can reveal variations in radiodensity within these soft tissue zones. For example, even in a normal foot, there is a subtle, yet distinct change in radiodensity between the laminar corium and the cornified inner layers of the dorsal hoof wall. Evaluating the soft tissue zones around PIII is particularly important in the diseased foot, because congestion, edema, or accumulations of inflammatory exudate or gas can alter the radiodensity of the tissue, in addition to altering its thickness.
Thus, a lot of useful information regarding the soft tissues of the hoof can be obtained, either directly or inferentially, if one only looks for it. This approach is particularly useful in the lame, footsore horse that has no radiographic abnormalities on “standard” foot films (i.e., no obvious bone pathology). Careful evaluation of the soft tissue zones surrounding PIII often reveals interesting details to the trained eye. As with clinical examination, it is important to develop an eye for fine detail and an appreciation for the range of normal (relative to breed, age, environment, and use) to get the most of a radiographic examination.
The coffin bone differs greatly from other bones in the limb; it is surrounded by a dense, cornified shell, whose thickness, density, and water content affect radiographic detail of the bones and soft tissues it encases, and even of the capsule itself. These characteristics of the hoof capsule must be factored into the radiographic technique.
Another unique feature of PIII that must be considered is its shape. The thickness and density of the bone differs markedly from proximal to distal, the bone being very thin and lacelike at its palmar/ plantar margin. In certain pathological conditions, this area can become even less radiodense. The radiographic technique must factor in this normal variation of bone thickness and density. The coffin bone cannot be thoroughly evaluated from just a handful of films, regardless of the quality.
Adequately imaging the navicular bone and adjacent structures presents yet another challenge. Not only are the navicular bone and related structures encased within the hoof capsule, they are also surrounded on three sides by PIII (and, on some views, overlaid by the second phalanx [PII]); therefore, superimposition of bone must be factored into the radiographic technique. Thus, thorough examination of all the structures within the foot requires several views and different exposure settings, each one tailored to best image the structure of primary interest.
Selecting Exposure Settings
For any radiographic view, the ideal exposure setting will depend on the equipment used (X-ray machine, screens and film, processor, etc.), the hoof mass, and the structure of primary interest. I use the terms soft, medium, and hard to describe the exposure settings I select for a particular view, depending on which tissue I am most interested in evaluating. (Note: Specific values for kilovolt peak (kVp) and milliampere seconds (mAs) will depend on the equipment used and the size of the foot being examined, and therefore, it is not possible to provide even general guidelines here.)
Soft exposures are for non-bony tissues, such as the horn and corium of the hoof wall and sole, and the palmar margin of PIII (Fig. 10A). A good soft exposure can reveal differences in radiodensity within the hoof wall, which allows differentiation between the laminar corium and the keratinized layers of the hoof wall. When looking for abnormalities at the palmar margin of PIII on the 65° dorso- palmar (DP) view, a very soft exposure is needed. If the perimeter of PIII cannot be seen without the use of a hot light, the view should be retaken at an even lower mAs (Fig. 10B).
Medium and hard exposures are used when the structure of interest is bone. Medium exposure is used for bony structures of moderate density or thickness, such as the body of PIII, and articular surfaces. Hard exposure is used for denser bone or superimposed structures, in particular, the navicular bone. I always use a 6:1 parallel grid when using a hard exposure setting.
As this approach illustrates, it is important to tailor the settings to the goal of the examination-- i.e., the structure you are most interested in evaluating. “Underexposed” is a relative term. What may seem grossly underexposed to others may be the perfect exposure to show soft tissue detail within the hoof wall or sole, or the palmar margin of PIII. Unless taking radiographs simply to guide farriery decisions, I take at least two exposures of each view: one soft and one bone detail (medium or hard) exposure. Soft tissue detail is essential, because the non-bony structures surrounding PIII are an integral part of virtually every foot problem.
Factors Affecting Image Quality
The diagnostic value of any radiographic examination is determined by the capability of two basic factors: the equipment and the examiner. The skills and knowledge of the examiner are as important as the choice and maintenance of the equipment (X-ray machine, cassettes, screens, film, developing and marking systems, positioning blocks). Not only does the examiner need a good working knowledge of clinical and radiographic anatomy of the foot (including an understanding of the range of normal), he/she needs good radiography skills, from a basic grasp of the geometry of radiation to experience with taking routine radiographic views. Good horsemanship skills are also important.
A disciplined, methodical protocol, designed to provide as much information as possible, is of primary importance if one is to get the most diagnostic value from radiographic examinations. Techniques for ensuring high quality radiographs of the equine foot are described in detail elsewhere1 and will only be summarized here. Several factors can affect image quality, and thus, limit the amount of accurate information you can obtain from your films:
- Preparation of the foot--thoroughly clean the foot of all debris, paying particular attention to the frog sulci.
- Beam positioning--the focal area of the primary beam is a zone 4 cm in diameter in the center of the beam; using the light guide or laser pointer, focus the beam on the area of primary interest.
- Beam-film relationship--make sure the cassette is perpendicular to the beam on all views; image distortion occurs whenever the film is not perpendicular to the beam.
- Subject-film distance--aim for a zero subject to film distance (i.e., cassette in contact with foot) to minimize magnification.
- Source-image distance (SID)--use a consistent SID; measure the distance each time, rather than “eyeballing” it.
- Hoof mass--always take into consideration the size of the foot; make separate technique charts for different sized feet, from foal to draft horse.
- Radiopaque markers--use markers to clearly and accurately delineate the dorsal hoof wall (lateral views) and, if the horse is unshod, the ground surface (lateral and DP views).
- Screens and film--use appropriate film to screen combinations and replace defective screens and cassettes.
- Developing solution--use developer at a consistent temperature set for your technique chart (contrast varies by approximately 10% for every 1°F difference); replace weak developing solution.
- Film marking--mark each film clearly and accurately; it is a permanent record and your “signature” to colleagues and clients.
Points 3 and 4. Beam to subject to film positioning is every bit as important as the exposure settings used. No matter how good the contrast and detail on the film, the radiograph may be non-informative or misleading if the structures of interest are distorted or obscured because of poor positioning. To minimize image distortion, the cassette must be perpendicular to the beam. Distortion will occur whenever the beam does not strike the film perpendicularly. To minimize magnification, the cassette must be in contact with the foot (i.e., zero subject to film distance).
Point 5. Several authors recommend a 40-in SID to minimize image magnification. I use a SID of only 24 in for all radiographs. I have found that the amount of image magnification is negligible between these two SIDs (40 and 24 in), and by using the shorter SID, I can use lower exposure settings, thus maximizing the longevity of my X-ray machine and minimizing radiation exposure to personnel. In my experience, beam to subject to film positioning is much more important than the length of the SID in minimizing magnification and image distortion.
Point 7. Let me reiterate how important it is to accurately delineate the dorsal hoof wall with radiopaque material for every lateral foot film. Even at a very soft exposure, you cannot know exactly where the outer surface of the hoof wall is; therefore, you cannot accurately measure dorsal H-L zone width unless the surface of the wall is marked. To paraphrase Murphy’s Law, it is on the cases that you do not think that you will need it that you will most wish that you had done it!
Furthermore, having the surface of the hoof wall outlined on every lateral film you take will soon train your eye to recognize subtle increases in dorsal H-L zone width, even before you get out your ruler. Almost without thinking about it, you will have added significantly to your range of normal data bank for this particular soft tissue zone.
It is not always necessary to remove the horse’s shoe for radiographic examination of the foot. The decision to keep or remove the shoe depends on the purpose of the examination. In fact, taking routine lateral and DP views with the shoe on can provide valuable information regarding the current shoeing strategy, such as balance, break over, and loading. However, leaving the shoe on limits the extent of the physical examination.
Depending on the shape, style, and fit of the shoe, and the horn growth since application, the shoe may obscure certain structures of interest on 45° and 65° DP views and 65° DP–45° lateromedial oblique views. The shoe may be superimposed over the palmar margin or wings of PIII, the coffin joint, and/or the navicular bone. In addition, scatter of radiation from the shoe can adversely affect image quality. (Fortunately, most of these structures of interest can be accurately imaged using other views, such as with the shoe on, without superimposition of metal or scatter of radiation.)
“Standard” views of the foot have been suggested as a guideline for practitioners. In my experience, they are of limited value, except as screening tools. They are inadequate alone for thorough radiographic examination of the foot. That is because beam orientation, positioning, and exposure settings should be selected in each case based on the purpose of the examination--the reason for performing the examination and the radiographic characteristics of the structure of primary interest.
Below are descriptions of the routine views I take: particular orientations and exposures that I use in most radiographic examinations of the foot. But first, it is important to reiterate that the value of the radiographic examination hinges on how well the physical examination was performed. Physical examination is the single most important aspect of examining the equine foot. With very few exceptions, the objective of the radiographic examination is simply to confirm the findings or suspicions of the physical examination. Relying on radiographic findings without a thorough physical examination and without consideration of the history carries the risk of misinterpretation and error, which can be costly.
When the principal item of interest is PIII in relation to the hoof capsule and the associated soft tissue zones, the beam should be centered 0.5–0.75 in above the bearing surface (i.e., close to the palmar margin of PIII), midway between toe and heel (Fig. 11). To accurately measure sole depth, distal H-L zone width, and palmar angle, the beam must be centered as close to the palmar margin of PIII as possible. These indices cannot be accurately measured when the beam is centered at or near the coronary band.
In most light horse breeds shod with a normal shoe, the palmar margin of PIII is approximately 0.5–0.75 in above the bearing surface of the wall. In Tennessee Walking horses and other breeds shod with a raised package or with an excess length of hoof wall, the beam must be raised accordingly.
Before taking the radiograph, ensure that the beam is horizontal and perpendicular to the sagittal plane of the foot, the cassette is positioned so that the entire foot is included and is centered on the film, the cassette contacts the foot, and the cassette is perpendicular to the beam. (Note: Lining up the heel bulbs by eye as a way of orienting the beam will result in a slightly obliqued view if there is even a slight disparity in the heels, because the beam will not be perpendicular to the sagittal plane of the foot.)
If the positioning block is an appropriate height and the X-ray beam is horizontal and centered between the shoe and the palmar margin of PIII, both branches of the shoe will be precisely superimposed (i.e., only one shoe branch is seen). If the foot is balanced lateromedially, both wings of PIII will also be precisely superimposed.
When the shoe branches are superimposed but the wings of PIII are not (i.e., one shoe branch and two wings are seen), it indicates lateromedial imbalance, which can be confirmed on the DP view. (Note: If the palmar margin of PIII is >1 in [25 mm] above the block, it may be necessary to raise the beam a little to accurately assess lateromedial balance on the lateral view.) If the shoe branches are not superimposed, it indicates a positioning problem, e.g., the beam is not horizontal and/or it is centered too high on the foot. Sole depth, palmar angle, and dorsal H-L zone width cannot be accurately measured on such a film.
The two exposures recommended for this view are soft and medium. The soft exposure is a “farrierinterest” view, because the information it provides can be of great use to farriers, as well as to veterinarians. Provided the dorsal hoof wall is delineated along its entire length with a radiopaque marker, this view allows accurate assessment of sole thickness, cup depth, medial–lateral balance, digital break over, dimensions and radiodensity of the H-L and C-E zones, and palmar angle. In addition, it reveals the profile of PIII and even bone detail along the thin palmar margin. I use this view in 100% of cases, because it is a blueprint for all therapeutic trimming and shoeing strategies.
Commonly diagnosed syndromes such as laminitis (with lamellar zone swelling and/or PIII rotation) and white line disease are easily confirmed with this view. Other lesions that may be evident on this view include fractures in the wing of PIII, proliferative bone changes along the dorsal face of PIII, and osteoclastic results of keratomas and other space-occupying masses within the hoof wall.
For a lateral view of the navicular bone or coffin joint, the beam should be centered just below the coronary band and a little closer to the heel--i.e., directly over the navicular bone or coffin joint. Other positioning factors are as described above for the lower lateral view. (Note: On raised lateral films, neither the shoe branches nor possibly the wings of PIII will be superimposed.)
The exposures recommended are medium and hard (using a grid). The medium exposure is best for evaluating the coffin joint. The hard exposure allows evaluation of the navicular bone and surrounding area, including the impar space. By providing a good short-axis view of the navicular bone, this orientation and exposure setting can reveal calcification or avulsion fractures associated with the impar ligament or the navicular suspensory ligaments.
When the principal item of interest is PIII in relation to the hoof capsule, the beam should be centered at the toe, 0.5-0.75 in above the bearing surface of the wall. Ensure that the beam is horizontal and parallel with the sagittal plane of the foot, the cassette is positioned so that the entire foot is included and is centered on the film, and the cassette is perpendicular to the beam.
For routine DP views, the cassette is placed behind the foot, as close to the heels as possible, while making sure that the cassette remains perpendicular to the beam. This approach produces a somewhat magnified, yet relatively undistorted image. The exposure recommended for this view is soft to medium. This exposure allows evaluation of PIII in relation to hoof capsule, hoof capsule in relation to ground, and thus, lateromedial balance. It also allows accurate evaluation of sole depth. These films are “farrier-interest” views.
The raised DP view is an excellent projection for evaluating the navicular bone. For this view, the beam is raised approximately 2 in (depending on the size of the foot), so that it is centered over the navicular bone. The beam is horizontal and all other positioning factors are as described for the lower DP view. The exposure recommended is hard, using a grid (Fig. 12).
If a problem involving the coffin joint is suspected, the raised DP view can be taken at a medium exposure. This view and exposure setting may also reveal fractures through the body or wing of PIII, proliferative bony changes along the palmar margin of PIII, side bone, extensor process lesions (e.g., cysts), and lytic lesions associated with PIII sepsis.
65° Dorsopalmar View
This view is the one most commonly used by clinicians to evaluate the distal margin of PIII and the navicular bone. Many practitioners set up for the 65° DP view by placing the cassette in a protective sleeve (tunnel) on the ground, having the horse stand on the tunnel, and angling the beam approximately 65° to the ground/cassette. Although it is convenient, this practice results in significant distortion of the image, because the beam does not strike the film perpendicularly.
Distorted images of the navicular bone carry an inherent risk of misinterpretation, because they do not accurately represent the architecture of the bone. For example, the normal radiolucent areas within the medullary cavity may appear elongated, widened, or otherwise misshapen on a distorted 65° DP.
It is far better to support the foot on a positioning stand, which allows the cassette to be placed perpendicular to the ground and thus, to the horizontal X-ray beam (Fig. 13). Although some amount of magnification is inevitable, this method ensures that the cassette is perpendicular to the beam, minimizing image distortion (Fig. 14, A and B).
Another potential source of error is failure to adjust for the angle of the navicular bone relative to the ground surface of the foot. Depending on the horse’s conformation and how the 65° DP view is taken (e.g., foot loaded or unloaded), the navicular bone may be more upright or more tilted back than expected, which will affect its appearance on the 65° DP image. It is worth checking the navicular bone angle on a lateral view (with the foot in the position for the 65° DP) before taking this view, because some adjustment in hoof position may be needed to get a true DP view of the navicular bone. For ex- ample, it may be necessary to take a 45° DP, rather than a 65° DP, to accurately image the navicular bone.
It is possible to get reasonably good detail on 45° and 65° DP views without removing the shoe, despite the scatter of radiation from the shoe. Often, however, the shod foot cannot be adequately cleaned, and the branches of the shoe partially obscure the navicular bone and the wings of PIII. Therefore, it is always best to remove the shoe for these views.
For evaluation of the navicular bone, the beam is centered over the navicular area and a hard exposure is taken using a grid. A medium exposure allows evaluation of the coffin joint, and the body and wings of PIII. A very soft exposure is indicated for identifying fractures at the distal margin of PIII (solar margin fractures) or changes in the soft tissue of the toe region. Remember that the bone at the distal margin of PIII is very thin and fenestrated with numerous blood vessels, and the mass of hoof that the beam must pass through at this level is relatively small, so a very soft exposure is needed to properly evaluate this area.
Note: For 45° and 65° DP views, it is very important to clean the foot and distal pastern thoroughly, paying special attention to the heels and the frog sulci to prevent superimposition of debris over the navicular bone and coffin joint. Even with a well-positioned, high detail film, failure to thoroughly clean the foot of all debris makes it difficult to properly evaluate these structures. In addition to thoroughly cleaning out any deep recesses in the frog, I trim the margins of narrow, irregular frog sulci, especially when the frog is very hard and dry. These narrow crevices create an air density over PIII and the navicular bone on 45° and 65° DP views that can be mistaken for a fracture line.
Packing the frog sulci and bar area with Play-Doh or similar material is a common practice when taking 65° DP views. I do not pack the foot with anything, because the packing material creates a subtle shadow on the film, which interferes with my interpretation of the underlying area. I much prefer the greater detail of an unpacked foot. (To test this yourself, pack only one half of the foot, take a 65° DP, and compare the detail between the packed and unpacked sides of the foot.) Another reason I do not pack the foot is because the farrier in me wants to see the outline of the frog and its sulcus--features I am already familiar with from having examined the foot thoroughly before taking radiographs.
65° DP-45° Lateromedial Oblique
When taking 65° DP-45° lateromedial oblique views, beam position may depend on the structure of primary interest. For example, the beam is centered a little higher for the navicular bone than for lesions in the toe region. Use a soft exposure for the wing of PIII (Fig. 9). This exposure can also be used to evaluate horn and soft tissue lesions in the quarter area, such as quarter cracks, bar cracks, gas-producing abscesses, and puncture wounds. A medium exposure is suitable for evaluation of the articular margins of the coffin joint. Use a hard exposure (with grid) to evaluate the wing of the navicular bone. This exposure also allows good visualization of the medial or lateral margin of the impar ligament attachment. Calcified lesions within the navicular ligaments, bone spurs, and medullary and cortical changes are all clearly demonstrated on this view.
The positioning block I use for 65° DP views can also be used to take a flexed lateral. This view is useful in extremely lame horses that cannot bear weight on the foot. It is also useful for evaluating the coffin joint and navicular area in other horses, because flexing the digit opens the dorsal and palmar aspects of the joint. The shoe does not limit the information gained from this view unless it poses a positioning problem.
Detailed discussion of the navicular bone and associated structures is beyond the scope of this paper. However, some general comments are in order. Perhaps most important is that no one view is adequate for proper examination of the navicular structures. Several views are required to adequately evaluate this part of the foot. In my experience, not only is the 65° DP inadequate on its own, it is perhaps the least informative view and the one most prone to misinterpretation, for the reasons discussed above.
I have found the raised DP view, using a hard exposure (with grid), to be a very informative navicular view, provided that the angle of the navicular bone is taken into account. This view can reveal abnormal radiolucencies involving the cortex and/or medullary cavity. A 45° DP (hard, with grid) complements the raised DP by allowing better evaluation of the wings of the navicular bone. The flexor surface, distal margin (impar ligament attachment), and proximal margin can be evaluated on a raised lateral or flexed lateral view (hard, with grid). Oblique DP views can also be useful for revealing navicular fractures.
The skyline (palmar proximal to distal) view has been advocated by some authors as the view to best image the flexor surface of the navicular bone. It can be a very useful view when taken correctly, because it can show cortical lesions along the flexor surface, particularly within the sagittal ridge. (Fig. 15) It also allows evaluation of the medullary cavity and the relative thickness and density of both cortex and medullary cavity, which can change with the stage of navicular syndrome. In addition, lesions within the deep digital flexor tendon (DDFT), because it runs over the navicular bone, may be apparent on this view, particularly if the lesion is calcified.
However, as with the 65° DP view, the skyline is easily misinterpreted if the image is distorted by poor beam to film positioning (i.e., when the beam does not strike the film perpendicularly) and if the angle of the navicular bone is not taken into account. Unless the angle of the beam precisely matches the orientation of the navicular bone, it is not the flexor surface that is brought into relief, but the proximal or distal palmar margin of the navicular bone.
To ensure that the beam and film are perpendicular, I use a positioning device designed to meet the parameters of the non-dictated view. The device is a box, 10 x 8 x 5 in with a durable Plexiglasb top. I place the foot to be radiographed on the device with the opposite foot on an elevated wooden block. The cassette is positioned under the toe through a slot in the Plexiglas. The tendon surface angle is then predicted from the external lateral view. The cassette is placed perpendicular to the pre-determined tendon angle using a simple protractor on the side of the positioning device. A 2-ft-long pointer is also used to accurately define the tendon surface angle and serves as a guide for the radiographic beam. To better understand this concept, take a navicular bone or a similarly shaped object in your fingers and sight down the flexor surface from proximal to distal. Rotate the bone around its long axis (i.e., replicate a change in angle of the navicular bone) and see what difference even a slight amount of rotation makes to the area that is thrown into relief.
With very few exceptions (only in grades 2-4 [moderate to severe] club feet) will the skyline view, taken as advocated by most authors, show the true flexor surface of the navicular bone. A good way of knowing whether your skyline image is truly showing the flexor surface is to take a series of skyline radiographs of an isolated navicular bone, each at a slightly different proximal to distal angle. The view that was taken with the true flexor surface in relief then serves as your benchmark when evaluating skyline radiographs of a horse’s foot (Fig. 16, A and B). Because of the complexity of the foot, every effort should be made to minimize distortion.
Note: When a lesion is found in any part of the foot or on any view, bear in mind that it takes two views, one perpendicular to the other (and both taken with the film perpendicular to the beam), to confirm the presence of the lesion and determine its precise location. Measuring the tendon surface angle of the navicular bone (lateral view) as it relates to the ground surface defines the proper beam angle for this view. Using that angle and a positioning block that allows perpendicular beam film alignment assures tendon surface relief.
Digitized radiography (i.e., generation of digital radiographic images) is increasingly being used in equine practice. Advantages include the ability to manipulate the image for enhanced detail (including soft tissue detail) and the ease with which images can be stored and transmitted electronically.
The initial cost is perhaps the greatest disadvantage. The ability to manipulate the image is also a potential disadvantage, because it may result in artifactual loss of detail, and thus, diagnostically important information. To get the most of any radiograph of the foot, whether conventional or digitized, it is important to have detailed knowledge of both gross and radiographic anatomy of the foot and an understanding of the range of normal.
Digital radiography offers enhanced image detail, but it can also be misleading when measuring soft tissue parameters. When printing radiographs, the printer dictates the image size. Most 8_10-in film is printed in twin format (two films, side-by-side, on one sheet of paper). To accomplish this, most printers shrink the image to 86%. Therefore, the soft tissue parameters must be converted to actual size. If not, your measurements will be skewed. Single format printing is preferred to ensure that one image, in actual size, is printed on each page.
Venography adds information about vascular perfusion to the details regarding bone and soft tissue structure already available from the plain films (Fig. 17). It can be an extremely valuable addition for diagnostic, therapeutic, and prognostic purposes and for monitoring responses to therapy. Venography can readily be performed in the standing horse, using routine X-ray equipment and easily obtainable supplies. 2
- Soft tissue pathology is a major cause of foot pain; seek information on the soft tissues in every radiographic examination you perform
- Develop a methodical approach, and use it every time
- Select exposure settings for particular views based on the structure of primary interest
- Develop a series of technique charts that allow for evaluation of different types of tissue (from soft tissue to bone) and different sizes of feet
- Take at least two exposures per view: one for soft tissue detail and one for bone detail
- Accurately mark the dorsal hoof wall with radiopaque material for all routine lateral views
- Measure sole depth, dorsal H-L zone width, C-E distance, and palmar angle on routine lateral views for all feet you radiograph to expand your understanding of normal
- Before taking any films, thoroughly clean the foot of all debris, paying particular attention to the frog sulci
- Focus the beam on the area of primary interest
- Make sure the cassette is perpendicular to the beam, on every view, every time
- Aim for a zero subject to film distance on all possible views
- Use a consistent source to image distance
- Make sure equipment and developing systems are functioning optimally
- Mark all films clearly and accurately
- Interpret all radiographic findings in light of the history and physical findings
4. Altering Mechanics as a Diagnostic Tool
Using a shoe that alters the mechanics of the foot can be a valuable diagnostic tool during a lameness exam. In addition, the horse’s response to the shoe provides valuable insight into how the healing environment within the hoof might be enhanced by altering the mechanics of the foot. This novel approach to examining and treating painful feet is very effective in the majority of footsore horses. Using a mechanical shoe to significantly relieve tension in the DDFT and on all related stress points often improves soundness within minutes of application.
Arriving at a tentative diagnosis after the physical exam, I usually take two survey radiographs with the shoes on and the horse alert (i.e., unsedated). The routine lateral and DP views described above provide all the information needed to assess hoof mass and balance and to identify the majority of common soft tissue lesions.
Most lame horses do not have bone pathology, so the solution in these cases generally relies on an understanding of how subtle changes in soft tissue parameters affect the overall health and soundness of the foot. The primary problem often involves soft tissue compression and associated vascular compromise which, in many cases, is the underlying cause of the pain and deteriorating hoof mass.
I grade the mechanical effect of the shoe or other therapeutic device as follows: one point is given for every 2° increase in palmar angle (with the horse bearing weight on the limb). Thus, a shoe with a mechanical score of one raises the palmar angle by 2°: this is a “low-mechanics” shoe. A device with a mechanical score of five is one that raises the palmar angle by 10°: the mechanical effect is described as moderate or intermediate. Raising the palmar angle 20° (such as is done for horses with acute laminitis) has a mechanical score of 10: this is a “high-mechanics” device.
Depending on the degree of lameness, the tentative diagnosis, and the horse’s training schedule, I usually start with a “low-mechanics” shoe. I move up the scale as needed, guided by the horse’s response and ability to readily unload the painful area in the particular shoe. I observe the horse at a walk and a trot, on soft and hard footing, on a slope, and on a 30-ft diameter circle. Figure 18, A and B, illustrates the effects of a “high-mechanics” shoe on palmar angle and functional break over.
5. Concluding Remarks
Effective examination of the foot hinges on an appreciation of its normal structure and function, encompassing the hoof capsule, soft tissues, vasculature, and bone. Clinical and radiographic examinations are merely discovery exercises, aimed at identifying the area(s) in which structural or functional integrity has been lost. This aim cannot be achieved without an understanding of normal, including an appreciation for the sometimes wide range of normal dictated by the horse’s breed, age, environment, and use.
It is not enough for us to reach a medical diagnosis; our examinations must have the dual goal of directing us toward a solution to the horse’s problem, for both immediate relief and long-range restoration and preservation of structural and functional integrity. That goal can be met only when our examinations are aimed at collecting as much specific information as possible, about every component of the digital unit.
Although it is important to tailor specific techniques to the goals of the examination, it is equally important to develop and practice a disciplined, methodical approach to both clinical and radiographic examinations. Errors of omission and misinterpretation are minimized when the examiner collects as much information as can be gained from both procedures and considers the significance of the findings in total.
Perhaps the single most important addition practitioners can make to their examination procedure is a radiographic protocol, which includes views and exposures that provide detailed information about the soft tissues of the foot. Making it part of every radiographic examination will greatly enhance your diagnostic capabilities by allowing you to develop an eye for fine detail, and thus, subtle abnormalities that would otherwise have been missed.
REFERENCES AND FOOTNOTES
a Intropaste, Barium Sulfate Paste, Lafayette Pharmaceuticals, Inc., Lafayette, IN 47904 or Yorba Linda, CA 92887.
b Plexiglas, Rohm GmbH & Co., KG, D-64293 Darmstadt, Germany.
Reprinted with permission from the 2003 Proceedings of the American Association of Equine Practitioners Convention
About the Author
Ric Redden, DVM, is known throughout the horse world as a veteriarian, farrier and educator. He owns and manages the International Equine Podiatry Center in Versailles, Ky, the first exclusively podiatry practice in the horse world. Dr. Redden is one of the world's foremost experts on laminitis and other hoof problems and travels internationally, teaching others his ground-breaking techniques and concepts.
POLL: Feeding Alfalfa